EDM recycled graphite filler in gypsum pastes
DOI:
https://doi.org/10.20868/ade.2017.3569Keywords:
Grafito, yeso, EDM, panel, Graphite, gypsumAbstract
Graphite can be obtained naturally or synthetically, but the latter has been used on roads because of its hardness, as well as in thin ceramic plates. The possibilities of the addition of the isostatic graphite powder from the milling of molds made by EDM in gypsum-based compounds are demonstrated. For this purpose mixtures of industrial gypsum with additions in different percentages of EDM graphite were prepared to evaluate the physical and mechanical properties, previously characterizing both materials. The gypsum was replaced by graphite in five different fractions, 5, 10, 15, 20 and 25% by weight, in the preparation of the mixtures. In the designation Y-0.7G-0 and Y-0.6G-0 of the series of prismatic specimens of 40x40x160mm, the letter Y refers to gypsum and G stands for graphite (G-0 test specimens without graphite) gypsum (a / y) 0.7 and 0.6. After the analysis of the results obtained, a new series was made with the addition of plasticizer and also with greater amount of graphite, 25 to 50% by weight and other ratios a / y based on their workability, to verify the incidence in the resistance to flexion and compression.
Downloads
References
American (2017). The American Carbon Society, http://www.europeancarbon.eu>.
Arikan, M.; Sobolev, K. (2002). The optimization of a gypsum-based composite material, Cem. Concr. Res. 11 (32) 1725–1728. https://doi.org/10.1016/S0008-8846(02)00858-X
CEDEX (2017). Centro de Estudios y Experimentación de Obras Públicas (CEDEX).
EN 13279-1(2009), Yesos de construcción y conglomerantes a base de yeso para la construcción. Parte 1: definiciones y especificaciones.
EN (2014). EN 13279-2, Yesos de construcción y conglomerantes a base de yeso para la construcción – Parte 2: Métodos de ensayo.
European (2000). European List of Waste, Commission Decision 2000/532/EC, 3rd May 2000, Off. J. Eur. Commun. L226/4.
European (2017). European Carbon Association, <http://www.americancarbonsociety.org>.
Flores Medina, N., Barbero-Barrera, M, Bustamante, R., (2016). Improvement of the properties of gypsum-based composites with recycled isostatic graphite powder from the milling production of molds for Electrical Discharge Machining (EDM) used as a new filler, Construction and Building Materials, 107, 17–27. https://doi.org/10.1016/j.conbuildmat.2015.12.194
Gao, L.; Shao, Z.C. (2012). The effects of graphite on ceramic coatings on LY12 aluminium alloys by micro-arc oxidation, Adv. Mater. Res. 454, 26–129. https://doi.org/10.4028/www.scientific.net/AMR.454.126
Gmouh et al., (2003) Changes in plaster microstructure by pre-stressing or by adding gypsum grains: microstructural and mechanical investigations, Mater. Sci. Eng., A 352, 325–332. https://doi.org/10.1016/S0921-5093(02)00938-3
Graphite (2017). .
Jeong, M.W.; Park, S.G. (2003). Heat-generating mortar powder using graphite and construction method using the same, Patente número KR2004090006-A.
Khalil, A.A. et al., (2013). Effect of different forms of silica on the physical and mechanical properties of gypsum plaster composites, Materiales de Construcción 63 (312) 529–537. https://doi.org/10.3989/mc.2013.04312
Khalil, A.A. et al., (2014). Effect of some waste additives on the physical and mechanical properties of gypsum plaster composites, Constr. Build. Mater. 68, 580–586.
Ley 22/2011, (2011) de 28 de julio, de residuos y suelos contaminados.
Maksoud, M.A.; Ashour, A. (1981). Heat of hydration as a method for determining the composition of calcined gypsum, Thermochim. Acta 3 (46) 303–308.
Sanz Arauz, D., (2009). Análisis del yeso empleado en revestimientos exteriores mediante técnicas geológicas (tesis doctoral).
Taylor, H.F.W. (1997). Cement Chemistry, second ed., Thomas Telford Ltd.
Yakovlev, G. et al., (2014). Utilization of blast furnace flue dust while modifying gypsum binders with carbon nanostructures, in: The 9th International Conference ‘‘ENVIRONMENTAL ENGINEERING”, eISBN 978-609-457-640-9. https://doi.org/10.1680/cc.25929
Downloads
Published
Issue
Section
License
Copyright (c) 2017 Autor / BY-NC
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
Anales de Edificación does not charge authors for processing or publishing an article and provides immediate Open Access to its content. All content is available free of charge to the user or his institution. Users are permitted to read, download, copy, distribute, print, search or link to the full text of articles, or use them for any other lawful purpose, without prior permission from the publisher or author. This is in accordance with the BOAI definition of open access.
- Authors retain the copyright and grant to the journal the right to a Creative Commons attribution / Non-Commercial / Non-Derivative 4.0 International (CC BY NC ND) License that allows others to share the work with an acknowledgement of authorship and non-commercial use.
- Authors may separately establish additional agreements for the non-exclusive distribution of the version of the work published in the journal (for example, placing it in an institutional repository or publishing it in a book).
Unless otherwise indicated, all contents of the electronic edition are distributed under a Creative Commons license.
